收藏本站
DS25LV02: Low-Voltage 1024-Bit EPROM
than t LOW0 , slave devices on the bus begin to interpret the low period as a reset pulse, effectively terminating the
transaction.
Figure 4. 1-Wire Bus Interface Circuitry
Vpullup
(1.8 to 5.5V)
Bus Master
4.7k W
Device 1-Wire Port (DQ)
Rx
Tx
Rx = Receive
Tx = Transmit
~0.5 μ A
Rx
~100 Ohm
MOSFET
Tx
TRANSACTION SEQUENCE
The protocol for accessing the DS25LV02 through the 1-Wire port is as follows:
§
§
§
§
Initialization
Net Address Command
Function Command(s)
Data Transfer
All transactions of the 1-Wire bus begin with an initialization sequence consisting of a reset pulse transmitted by the
bus master, followed by a presence pulse simultaneously transmitted by the DS25LV02 and any other slaves on
the bus. The presence pulse tells the bus master that one or more devices are on the bus and ready to operate.
For more details, see below.
NET ADDRESS COMMANDS
Once the bus master has detected the presence of one or more slaves, it can issue one of the net address
commands described in the following paragraphs. The name of each Net Address command (ROM command) is
followed by the 8-bit opcode for that command in square brackets.
Read Net Address [33h]. This command allows the bus master to read the DS25LV02’s 1-Wire net address. The
bus master follows the Read Net Address command with 64 read timeslots allowing the 1-Wire slave to transmit its
address. This command can only be used if there is a single slave on the bus. If more than one slave is present, a
data collision occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result).
Match Net Address [55h]. This command allows the bus master to specifically address one DS25LV02 on the
1-Wire bus. Following this command, the bus master transmits the 64 bit net address of the desired slave device.
Only the addressed DS25LV02 responds to any subsequent function command. All other slave devices ignore the
function command and wait for a reset pulse. This command can be used with one or more slave devices on the
bus.
Skip Net Address [CCh]. This command saves time when there is only one DS25LV02 on the bus by allowing the
bus master to issue a function command without specifying the address of the slave. If more than one slave device
is present on the bus, a subsequent function command can cause a data collision when all slaves transmit data at
the same time.
Search Net Address [F0h]. This command allows the bus master to use a process of elimination to identify the
1-Wire net addresses of all slave devices on the bus. The search process involves the repetition of a simple three-
10 of 17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS2704G+T&R IC EEPROM 1.25KBIT 6TDFN
DS28CZ04G-4+T IC EEPROM 4KBIT 400KHZ 12TQFN
DS28DG02E-3C+T IC EEPROM 2KBIT 2MHZ 28TSSOP
DS28E04S-100+T IC EEPROM 4KBIT 16SOIC
DS28EC20+T IC EEPROM 20KBIT TO92-3
DS301X KWIK-CHG DESIGNATION STRIP SGL
DS3030W-100# IC NVSRAM 256KBIT 100NS 256BGA
DS3045W-100# IC NVSRAM 1MBIT 100NS 256BGA
相关代理商/技术参数
DS25LV02RR 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage 1024-Bit EPROM
DS25LV02RT 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage 1024-Bit EPROM
DS25LV02RU 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage 1024-Bit EPROM
DS25MA-BK 制造商:Sealcon USA 功能描述:
DS25MB100 制造商:NSC 制造商全称:National Semiconductor 功能描述:2.5 Gbps 2:1/1:2 CML Mux/Buffer with Transmit De-Emphasis and Receive Equalization
DS25MB100_0712 制造商:NSC 制造商全称:National Semiconductor 功能描述:2.5 Gbps 2:1/1:2 CML Mux/Buffer with Transmit De-Emphasis and Receive Equalization
DS25MB100-EVK 功能描述:其他开发工具 DS25MB100 EVAL BOARD RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压:
DS25MB100TSQ 制造商:Texas Instruments 功能描述:Multiplexer/Buffer 36-Pin LLP EP T/R